GQ Electronics Technical Support Forum Active Users: / Visits Today:
Highest Active Users:
GQ Electronics Technical Support Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 GQ Electronics Forums
 3. GQ EMF EF Meter RF Spectrum Power Analyzer
 Measuring EMF from 4G or WiFi at at a distance
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

garibaldi

3 Posts

Posted - 10/07/2018 :  06:52:48  Show Profile  Reply with Quote
I recently purchased a GQ EMF-380 meter for measuring EMF from various sources. I currently have a cable modem for Internet am considering switching to a a 4G-based Internet solution for a much smaller cost. I have a detached garage with ethernet going to it so I could place this 4G Internet receiver in my garage and use the ethernet cable to bring the Internet to my house. This would keep the 4G a decent distance from my house. I have not yet tested it, but I am guessing I won't see any increase in the mG on the meter when inside my house once I have this 4G Internet device installed (because of the inverse square law). If that is the case, should I be concerned about it causing more EMF inside my house if I can't measure it this way with the meter? I know it would obviously be communicating with the tower and therefore there would be more waves in the air than before, but is this a problem if the meter is not registering an increased mG value inside my house? Similarly, I can measure an increased mG near my WiFi router, but elsewhere in my house the values are very low. I'm trying to understand if there is some other way of measuring EMF or RF at a distance that I should do? Thanks!
Reply #1

EmfDev

2132 Posts

Posted - 10/09/2018 :  09:28:34  Show Profile  Reply with Quote
Hi garibaldi, The RF sensor might still be able to pick it up. But if that's far away, then you shouldn't have to worry
about high EMF from inside the house instead you monitor RF density.
Go to Top of Page
Reply #2

garibaldi

3 Posts

Posted - 10/10/2018 :  18:36:09  Show Profile  Reply with Quote
Thanks for the help! So to clarify, I should use the "Horizontal Mode" or "RF Graph" mode and watch the mW/m2 value over time to obtain an average RF density? These two modes seems to disagree - "Horizontal Mode" shows around 8 mW/m2 while I'm just holding the EMF-380 in various places not near any device (and I turned my WiFi router off). However, "RF Graph" shows a value around 0.15 mW/m2 in these same places. It seems like 8 mW/m2 not near anything and with my WiFi router is a high value, doesn't it?

Edited by - garibaldi on 10/10/2018 18:47:46
Go to Top of Page
Reply #3

EmfDev

2132 Posts

Posted - 10/11/2018 :  08:28:26  Show Profile  Reply with Quote
You should monitor the Horizontal/Vertical RF Mode as it also picks up signals in different ranges. Or you can try the 240MHz - 1040MHz in RF Graphs to check if it picks up 4g signal from the tower or your router. By the way, what banddid the 0.15 mW/m2 came from? is it from the 2.4g? Thanks!
Go to Top of Page
Reply #4

garibaldi

3 Posts

Posted - 10/11/2018 :  16:13:05  Show Profile  Reply with Quote
Ah, I understand now. The 8 mW/m2 in Horizontal RF Mode is in the range of 664Mhz - 689Mhz so maybe a weak LTE signal from somewhere else? I don't have the 4G device on when I'm taking these readings.

The 0.15 mW/m2 on the RF Graph screen was showing up in the top-right corner at around 2.43Ghz to 2.44Ghz.
Go to Top of Page
Reply #5

EmfDev

2132 Posts

Posted - 10/12/2018 :  08:36:53  Show Profile  Reply with Quote
Yes, the 8 mW/m2 didn't come from the 2.4GHz band. If you use your microwave, you will see the number shoots up.
Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
GQ Electronics Technical Support Forum © Copyright since 2011 Go To Top Of Page
Generated in 0.05 sec. Snitz's Forums 2000